The start button on my Janome Star long arm machine works sometimes and sometimes it doesn't. I suppose it will need to be repaired.
My best friend has these machines and she said to first try carefully cleaning around the button with a very fine brush as it could just be a lint build up that is causing the button to be wonky.
This is an example of what is out there on YouTube if you are handy and want to try a DIY fix. I wouldn't, but that is me...I am all thumbs:
www.youtube.com/
Post back what you learn!! Hope it is as simple as a good cleaning!
While researching another problem, I read an article on Janome forum that you could use the spray that is used to clean computers but I have not tried this so I'm only relating what a "repair" shop person suggested.
It was suggested to turn off the machine and just spray the area/opening with a short burst and wait a few minutes before using the machine.
This spray can be found at most large stores or online.
www.walmart.com/
I have intermittent stitching on my Gammill Statler stitcher. I can start stitching and it will stitch and inch or two. Then stops. I can restart stitching and it will again just stitch an inch or two. I changed the red control handles and that made no difference.
I have a Husqvarna Mega 18 x 8 Quilter that turns out to be nothing more than a tin lizzie. I had thread to hang up in the bobbin cace and I turned it off and removed the thread. When I turned it back on it started powering up as it is suppose to do, but all of a sudden it went completely out, like the power had gone out. I had an electrician come out and check my outlets for any issues and he put a meter on the mother board.
The cord is hot up to where it goes into the mother board. There is no one near me that works on this machine, I'd have to take it to another state. I feel this is a mother board issue. Any help is greatly appreciated.You are correct the motherboard is fried and needs to be changed out. Maybe you can try to order one online and take it to a computer shop in your area. The reason I suggest this is because a computer shop could easily change the motherboard out for you and get it up and running again.
My TinLizzie18 is sick. It turns on, gives the error code "uC", and then the screen turns to the normal "start sewing" screen. When I press the foot pedal, the machine moves lightening fast. Not even a professional quilter would move that fast.
I can't make it slow down (releasing the pressure on the foot does nothing. Changing the speed does nothing.) The only way to stop it is to turn it off. Oh, the TinLizzie company has since gone out of business, so I can't call/ask.This is an expensive machine but boy are there a lot of negative remarks posted everywhere about this company and machine.
The only suggestion I can offer is to try and contact a quilting club that uses the TinLizzie18. I'm sure you probably have one in your area but you can Google TinLizzie quilting with your zip code and see what turns up.
Here is a link you can check out - email address near the bottom. They may be able to help you.
www.sewingmachinesplus.com/
Here are a couple of YouTube videos that might have something useful
www.youtube.com/
www.youtube.com/
I can't figure out how to install the belt system for the Y axis on my Gammill Statler Optimim longarm quilting machine.
Someone please help!
Since you are a quilter, I feel sure you are acquainted with someone in your area that belongs to a quilting club.
Or, if not, Google Quilting clubs with your zip code and try to contact someone in your area.
I get a lot of my 'who to contact' people from my local craft stores as this is where the majority of sewers and quilters buy their supplies and almost everyone at some point in time have problems that need answers (with instructions).
I have found that quilters love to help other quilters so I hope you will find this to be true in your area also.
We have contacted Gammill and other resources and we were still unable to figure it out. Was also told no one available for a service call for at least two to three weeks. We finally found a technician yesterday evening and he is scheduled to come out later this afternoon. So, weve been down for almost 3 days.
My long arm stopped working. The needle wouldn't move. I turned the wheel clockwise and counter clockwise and cleaned out the bobbin casing area.
Now the needle hits the casing when I try and move the needle. How can I adjust the casing so the needle moves freely and enable me to sew?The timing is off. There is an article with pictures here.
I have an Artistic 18 long arm sewing machine. It keeps shutting off. Any ideas?
You have an electrical short somewhere. Unless you know about sewing machines, take it in for servicing.
how old is it? have you moved it around too much? It sounds like theres a wire frayed somewhere or a connection that's not being made.
My longarm quilting machine jammed, and I disgorged a lot of thread, but the shaft doesn't turn and the motor grinds when I turn it on. I know it isn't a thread birdnest anymore, causing my machine to freeze.
Could it be that the motor belt was torqued? The handwheel is just as tight as the shaft. I'm using a Nolting Hobby Quilter, and I love it! Just help me out of this (literal) jam, all you quilting gurus, please.You need to remove the protective cover from the flywheel belt. Here is a video that explains. tinlizzie18.com/
My machine went into high speed and the needle broke. I shut off the machine and changed the needle. Now it skips stitches. I cleaned the machine and changed the needle again. I also changed the bobbin. It still skips stitches.
By Ruth G. from Oberlin, OH
It sounds to me like either the tension needs to be adjusted, or you have the bobbin in upside down.
I am experiencing poor stitch quality on my Gammill Optimum and Statler Stitcher, long arm quilting machine. My tension is good when stitching in one direction, but poor going the other way. The repair techs have been here 4 times. The hook assembly was replaced, but the stitches are slightly worse.
By Denise O