I have an Usha Janome sewing machine. The thread gets cut in a few stiches. Is it a problem with tension?
The tension may be too tight, the needle may be threaded incorrectly, the thread may be old or poor quality, or the needle may need to be changed.
I have a New Home 532 sewing machine from 1963 and it has been the best sewing machine for me. I had it serviced about 10 years ago, but it might need it again.
I cannot get it to sew. The light is on, but it seems that the machine is not getting any power to the sewing mechanics.Referring to the owner's manual, clean and oil all the moving parts of the machine. As a machine sits unused for a long time, the moving parts seem to "gum up" and not move like they should. Cleaning out all lint, loose thread, etc, AND re-oiling should do wonders for getting your machine back to working order. Also make sure the foot pedal cord is undamaged and fully plugged in.
I had not used my Janome 7500 machine for several months. Then when I took it out to sew, it would not turn. After moving the wheel by hand using a fair amount of pressure, it moved then I was able to use it. My husband then cleaned it out and greased some of the moving parts and all was well.
There was a lot of fluff in the machine. I have now tried to use it after leaving it for a few months and it is completely frozen and I cannot get anything to move and then a beeping sound started so I have turned it off. Any ideas as to what the problem could be? Thank you.You sound like you could have a frozen motor in the machine, a belt could be broken, or you need a really good cleaning. There could be some rusted parts that are causing the machine to no longer turn. You should try once again to clean the machine. Normally the only area you are to oil is the area for the bobbin and not the rest of the machine.
Here is a couple of good videos that you can watch to help you out.
www.youtube.com/
www.youtube.com/
www.youtube.com/
I know the videos are not for your exact sewing machine but all sewing machines works the same. These are 3 different videos that will help you and your husband to get your sewing machine unstuck and working again.
First of all, I know that you should not force the wheel to turn but try to find the problem first.
I do not know what type of oil(?) your husband used when he 'greased some of the moving parts' but if he did not use genuine sewing machine oil (not WD-40 or any other type of oil) then this could be your problem.
Finding and fixing the problems can take several steps but most of the time it is best to follow a set pattern as this is the way the sewing machine techs fix problems.
Here is a very good outline - step by step - on how to unfreeze a sewing machine because this is a common problem and instructions will fit almost any machine.
sewingmachinebuffs.com/
You can also join a sewing machine forum and ask your questions there as these members are all 'techs' in the common sense of the word and help people with problems everyday.
This is a good site to keep handy as I feel sure there will be more problems in the future and this site has all sorts of information - you'll love it.
My Janome Memory Craft 9459QCP has stopped working after the needle bent during my Free Motion Quilting. I have turned it on and off several times for periods of time, and I still get this message.
It will not raise the needle. Is there a way to reboot the computer system?
I haven't used my New Home Memory Craft 7000 for a few years but got out today to do some zig zagging of edges. Thought I had threaded properly but after a few stitches, it jammed and I had to cut threads to release fabric.
Took plate off under where bobbin is and needle doesn't seem to be taking up bobbin thread. Any ideas please?This is not too hard to repair. You just have an issue of threading the machine incorrectly and not installing the bobbin in the right way. it would also help if you took apart the bobbin canister and the holder to do a good cleaning of this area before you start again. Remove all the lint and dust in his area using a small brush. Now add 1 drop of oil here and not more. Put this back together and now take your bobbin and put it back in the canister. Watch how you thread this canister to make sure the thread is moving correctly.
Is a New Home Memory Craft 7500 worth getting repaired if it says communication error?
Have you tried resetting it? Your manual would have how to reset. Also make sure it is not clogged with debris. This will hinder the machine if there is anything built up inside , therefore throwing a error code. Clean out , reset, and try again before giving in! Here is a link to others with trouble shooting - sewing.patternreview.com/
Communication error is not that hard to fix on most sewing machines. The machine could have taken a power surge or when plugged in was not connected correctly. I would start off by resetting the sewing machine. Your user manual has these instructions in the back of the book under troubleshooting. Follow the directions and reset the memory card in the machine. If this is not helping out then there could be an issue with this memory card and it may need to be replaced. I would consult a repair shop because the machine is electronic and at times it is harder to torepair at home if you don't have the experience. See how much the repair shop will charge you to replace this card.
I have a Janome DC2011 sewing machine. When I zigzag stitch, I found that the needle arm bumps into the needle threader at the highest point in a single stitch. Can I repair this myself?
You do not say how long you have had your machine or if this is the only problem you are having but if it is a 'newly' acquired machine then I would suggest you contact someone where you purchased your machine and ask for help.
If this is not possible then my next suggestion would be to contact Janome and ask for help. They will probably direct you to an area Janome dealer but they may help you if they can see your machine. I would ask for a price before letting them do anything to the machine.
If you have a Michael's or Jo Ann's near-by you could ask them if they have the name of a Janome repair person that might help you.
You can also Google Sears Service Center with your zip code for a center in your area. If you call and they are open then you can take your machine to the shop and ask for help. If everything on your machine is in good shape then you may not need for it to be serviced so just ask if they can tell you if you need a part or what do you need to do to fix it.
These are expensive machines so you should be able to find someone that can tell you what you have set up incorrectly that is causing this to happen.
There are also several sewing machine forums that will help people with problems so maybe check some of these out. You will have to join (free) to ask questions.
Sorry that I could not be of more help but this is not a machine that I ever seen or worked with.
Here is a link to a PDF manual if someone needs it.
I have the model 415 and I think you are talking about the small plastic level on the side of the needle that you pull down and put through the eye of the needle to thread the machine. if this is the case then the plastic piece is bent and this is your issue. When you lower this piece it should lower down behind the needle and then when you reach the eye of the needle you push it forward. Once the thread is on the hook you can move it backwards and lift it up. This threads the needle. The piece should be up high and towards the back and not forward. If it is forward you have an issue with the spring on the needle threader. You may have a bent spring that needs to be replaced. You can try and remove the screw on the side and take a look at this one. It sounds like this piece needs to be replaced.
My machine is working for normal sewing, but the overlock needle bar won't move. I have changed the needle, checked all tensions, and cleaned all the dust out.
It sounds as though it's time for your New Home to have a visit with a professional repair tech. You've noted changing needle, checking tension, cleaning dust, so I'm assuming you've also followed the user manual instructions for the settings needed - after those boxes are ticked there is usually only one reason a machine won't sew - a broken or worn gear/part/assembly within the machine. Generally this isn't something that can be handled at home - a pro has the service manuals, tools, and training to work out and repair the problem.
I am restoring to working order, my wife's great aunt's New Home Treadle Sewing Machine. It is missing the spring loaded part that locks the handwheel to the belt pully.
I can use a small bolt to lock these two together, but when would one wish to uncouple the handwheel from the belt pulley?
