I have a Maytag Maxima steam x front load washer. I have had to call a repair tech once and it cost $200. In mid cycle it throws e01 and f08 codes, the door will not unlock and there is no power. It just did it again a week after repair. Here is my tip.
My washer won't quit draining. It showed codes F03 E01 then all lights on the panel went off and it is still draining. I have unplugged it and when I plug it back in shows same codes and keeps draining.
The door is locked. Any ideas how to fix or at least quit draining and unlock?My Maytag washer, unknown model number, it is unreadable is showing code Du and then F. It won't unlock. Anybody know what this means?
Thank you.
I have a Maytag Maxima MHW6000XW and it is giving a code of F06 and E02. What does this mean?
I have replaced the hoses cold and hot, checked inlet valves, cleaned out drain, and cleaned out inside drain hose. I cleared the inside filter and checked the valve inlet hose for holes.
The washer still throws error, 25 minutes into the cycle and we have to drain it. What else could it be?I have a Maytag washing machine that does not start and displays "lid" as fault. I have to unplug the washing machine, and plug in again, then it starts the wash cycle.
If this a lid switch that is bad?I have a Maytag Bravo MVWX700XW1 washer. What does error code F7 E1 mean and how do I repair it? Thank you.
The error code F21 is displayed on my Maytag front load washer. How can I fix it?
My Maytag front load washer will not start. It flashes the letter "F" then the number "11".
my maytag washer runs fine, untilit gets to the spin cycle. when it get to the spin cycle it flashes f9 or e1
I have a Maytag Neptune Washer MAH5500BWW. The service cycle displays code PA and h. What are these codes? The washer won't start, the display board works, and it runs a service cycle.
My front load machine is showing an error code 3E. What does that mean?
I am in need of some assistance that the kind of folks at Maytag are either unable or unwilling to perform. My washer, three years old, is giving me an error code of 'f6 e1' followed by three rapid beeps. It's part of the 2000 series (the one with only bad reviews on Amazon), model #MHWE201YW00.
I have already swapped out the machine control board at the advice of a local serviceman, and before I light more money on fire I figured the wise sages of the internet could render better assistance than I've received thus far.
Thanks for solving my first world problem.
I have a Maytag 9000 series front load washer. I had an error code "f28". The repair man came out said it was the motor control panel so they replaced it.
Now its throwing an "f99" code and nobody can figure it out do you have any ideas?I have a Maytag front load washer. Once I set the cycle the estimated time remaining shows the proper time, like "45 minutes". Once I start the machine, it starts to fill with water (I'm not sure if it fills completely), then it often will start to wash a bit.
Next, it beeps and the display in the estimated time remaining flashes a "H" then a "F", but will not complete the cycle. It just continues to flash these to letters (one after the other). I don't know what it means or how I can get it to wash.I have a Maytag Maxima front loader. We kept on getting error codes for plugged drain so we cleaned out the hoses and took off the front panel and cleaned the lower filter which was pretty nasty. There were kids' socks, toys, and almost $5 in change, but we put it back together and tried to start a load and all it does is beep a few times in a metallic tone then shuts down.
I believe it threw out a code of INT at one point since we put it back together.I have a small Maytag washer model: MHWC7500YW. It stopped working during the washing cycle. I have unplugged it and then it works again for 1 or two loads max; and then stops again flashing the F23 error code. What is this and how I can fix it?
Thanks.
Our 3 year old front loading washing machine is showing error code F08. Can you help us diagnose the problem please?
