social

Bobbin Getting Tangled

October 30, 2010

Bobbin with Green ThreadMy sewing machine was working fine until I took the plate off to clean out the dust and stuff underneath it. When I put everything back on and turned my machine back on and started to sew the bobbin started pulling and jamming. Then I have to pull out the fabric and it has a lot of thread on the bottom like it is pulling lots of thread. The machine keeps stopping. What did I do? Can anyone help.

Advertisement

By Donna from FL

Answers

October 31, 20100 found this helpful

If this happens on my Elna it means that the Bobbin is either in, upside down, OR I have NOT threaded the feed from the spool of thread properly. Often it will do this on its own.

 
October 31, 20101 found this helpful

Please see answer above. Note; you can tell if Bobbin is upside down (in wrong) if the thread is NOT turning counterclockwise. Must turn counterclockwise. Also, make sure that you have not inadvertently bumped the tension adjuster. Helps if we know the make of the machine, as adjustments differ on each brand. Cheers!

 

Bronze Feedback Medal for All Time! 186 Feedbacks
October 31, 20101 found this helpful

I have had this happen occasionally, but not enough to be bothered about it. After about 60 years of sewing almost everything, it took me until about 10 years ago to discover that you definitely shouldn't start a seam at the very edge of the fabric.

Advertisement

Whenever I would do that I would end up with the thread and edge of seam "gnarly". Then one day I read that to prevent that from happening you should start sewing about 1/4" in from the edge of the fabric. It's amazing what that does.

 
July 2, 20160 found this helpful

Thanks for all the comments. I cleaned out as recommended and it still wasn't working. Turns out I was using the wrong settings. Thanks again for all the advice. Super helpful.

 
Read More Answers

October 7, 2013

The bobbin thread is catching and bunching up under the fabric. I can sew a few stitches (3-4) then my thread catches. When I pull the fabric up (quite forcibly) there is a ball of tangled thread underneath. What am I doing wrong?

By TAJDunk

Answers

March 1, 20170 found this helpful
Best Answer

As per previous answers the problem is caused by the setting on your machine. Tension wheel needs lowering in number.

 
Answer this Question

October 30, 2011

View into the bobbin area of machine.I have a top loading Singer heavy duty 4411. I got it today and it worked fine for a while, then for some reason it would jam. When I managed to get the fabric out, I saw that string from the top had gotten tangled in the bobbin casing. It was so bad that I had to cut the threads out and pull out the fibers.

I've tried re-threading, rewinding, and re-everything! The bobbin is in the right way, I have already switched out the needle, and this is a brand new machine. Even if I just turn the handle manually without a bobbin, the thread still gets caught around the bobbin casing in the same places. I have no idea what to do and I need to finish my Halloween costume for tomorrow. Please help.

Advertisement

By John D.

Answers


Silver Feedback Medal for All Time! 282 Feedbacks
November 3, 20110 found this helpful

I hope you were able to get your costume done in time. It sounds as if the problem might be that the bobbin tension needs adjusting. Even though you have a brand new machine and the tension was adjusted at the factory, it's possible that it was un-adjusted during shipping. Or the entire bobbin casing could have come from the factory upside down, I've heard of that happening.

Or you could be using the wrong needle and thread for your project, the pressure could adjusted incorrectly. The thread could be old (even if you just bought the thread the day before you started the project, because a lot of the threads in the store racks are anywhere from 1-5 years old.

Advertisement

The older the thread the more troubles it can cause during sewing).

Actually, there are several reasons this could be happening and most of those reasons are usually 'pilot error', lol. Check the manual section on troubleshooting your machine, should have info there on what's happening.

Don't give up, you have a fine machine there that should give you years of reliable service.

 
January 13, 20151 found this helpful

Hey I have the same machine and had to pack away my project when the thread from the top kept tangling in the casing for the bobbin. What I also noticed was that the hand wheel was a little stiff when I turned it. A few days later I decided to give it ago again put the problem persisted.

Advertisement

I decided to removed the metal top which housed the bobbin and used a small brush to remove any dust (even if you can't see any still carefully bush the insides while turning the hand wheel). I continued this until the hand wheel started moving freely. I retreaded the machine and that solved the problem. Hope this helps someone.

 
January 15, 20150 found this helpful

I just bought the same machine today (1/15/15). I was sewing "sew-on" Velcro to neoprene. I sewed two 4"X2" pieces and then the machine was done. 2 or 3 stitches and then the hook/bobbin was totally jammed with thread. upon closer examination, it seems the hook would catch the thread the first time, but the bobbin thread would not come up through the plate.

Advertisement

As the hook rotated around, it would pull more thread off the bobbin until it was a complete mess. I called Singer and after 15 minutes on hold, the recording said they were now closed. I'm going to try the cleaning recommendation and if that doesn't work, I am going to try to return it tomorrow. At $129 it seemed like a good buy for a "Heavy Duty" machine.

 
February 25, 20150 found this helpful

I want to know why my thread keeps getting tangled in the bottom bobbin on my sewing machine.

 
October 3, 20150 found this helpful

I have a similar machine and sometimes the thread falls off the thread take-up lever. Try rethreading the top thread.

 
Read More Answers

February 19, 2016

I bought a sewing machine at a yard sale and I can't get the bobbin to work. It gets tangled in the bobbin case. What can I do to get it working right? It's from Italy and is called a Stretch _Sew machine. Any help would be appreciated.


Read More Answers

October 30, 2010

I was given a sewing machine, and there's a problem. When I am sewing the bobbin gets all tangled up, I will get one or two good stitches then nothing. When I turn the material over there is a ton of thread from the bobbin. Has anyone else had this problem? How did you correct it?

 
Read More...

March 8, 2014

Tangled thread and bobbin case.I have a Singer 1120 sewing machine that is giving me threading problems. When I sew it'll jam up or get stuck mid-way. When I stop to check what is wrong and I pull the testing fabric I notice a lot of thread is coming from the bobbin area. I've done everything from re-spooling the bobbin, reconnecting it, to even re-threading it and it's the same thing over and over. I've even checked the timing and the timing is still good on it. Please help.

By Sharon

Answers


Silver Feedback Medal for All Time! 282 Feedbacks
March 10, 20140 found this helpful

First of all - either check your manual troubleshooting pages, or download this free copy from the Singer website:

www.singerco.com/.../9c027eede5e1c63fb69b05759228e608f6b0537a...

The troubleshooting guide is on page 74. You may want to print this out to have on hand without having to have the computer up:)

Now, have you checked your bobbin case, the area where the bobbin case seats back into the machine, and the area under the throat plate (where the feed dogs come up through to the top) for bits of debris (thread bits, fuzz, lint, etc)? That's usually what causes the problem you're experiencing. *Don't use an air spray duster! This will only blow the lint further into the machine. Instead, use a mini-torch (flashlight) to look, then long tweezers or a skinny paint brush to remove any debris.

If that doesn't help, go through the following, and if those don't solve your problem it's time for a visit to the Singer repair tech:

Are you positive you're seating the bobbin case into the machine correctly? You've probably been doing this for years but on older machines with that front (or side) load system the catch wears and sometimes it helps to follow the insertion instructions step-by-step from the manual.

Are you using the correct needle, thread, tension, and feed dog settings for the fabric you are trying to sew?

Are you alining the fabric start edge completely under the presser foot before starting to stitch, or have you got into the habit of starting your stitching with the fabric edge lined up with the needle instead of the presser foot end?

Are you holding the thread tail taut (but not too taut - you're 'helping' not pulling!) when you start stitching to help the fabric along through those first stitches? (Especially helpful when stitching very fine or very thick fabrics)

Again, if the above doesn't help it may be time to take the machine in for servicing. Your machine is an older one, and may have some worn plastic or silicone gear teeth that need to be changed.

 
March 10, 20140 found this helpful

Get out your manual if you have one and check the directions for checking bobbin tension. Usually a screw in the bobbin case.

 
Answer this Question

April 9, 2018

I have a Kenmore sewing machine and I put in a new bobbin, but when I tried to bring up the bobbin thread the top thread catches on the stopper in the hook race. I am not sure what happened it never has before.


Read More Answers

July 18, 2016

I'm ready to throw my Singer Tradition sewing machine out of the window. I'm about two thirds of the way through making a dress and now the thread keeps getting caught above the bobbin so that there are several threads coming up through the hole and everything jams.

I ran out of thread in the bobbin so I made a new one and since then the machine gets jammed after sewing successfully for about 20-30cm. It works fine up to that point.

I have rethreaded the top and bottom several times, made a new spool, taken the whole thing to pieces for a good clean, changed the tension on the top and bottom, put in a new needle, tried different fabrics, and tried using different thread. After every troubleshooting attempt the same thing happens: it sews fine for 20cm and then jams up.

I am completely out of sensible ideas. The manual for this machine is useless. My next attempt will involve getting out a screwdriver and taking the entire machine to pieces.

Answers


Gold Post Medal for All Time! 969 Posts
July 20, 20160 found this helpful

Breath...I know this problem and think I can help. If your bobbin thread is "misthreaded" even by a couple of rows, it will mess you up. I make sure when I wind a bobbin that it goes up and down, "bouncing" off each side so the thread is wound evenly.

If this isn't the case, it might be that your thread is not "catching" properly.

If this doesn't help you might need to see a sewing repair person. Or, check with your local thrift store and find a nice second hand one. Even the new ones might be cheaper than repair...which can be spendy.

I hope that helps.
PBP

 
Answer this Question
<< First< Previous
Categories
Home and Garden Repair Machines Sewing MachinesMarch 11, 2014
Pages
More
🐰
Easter Ideas!
🌻
Gardening
👒
Mother's Day Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-03-28 01:43:56 in 8 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/Bobbin-Getting-Tangled-1.html