Wiring Diagram for John Deere Riding Mower?Wiring diagram for a 214 John Deere riding mower?
Wheels for Blue Ribbon Reel Mower?Need wheels for a blue ribbon reel mower. The steel wheels say ball bearing D2. Do they have rubber on them or not?
Repairing Sewing Machine?I have a Singer 2277 sewing machine that is jamming up. It began after I tried to sew in reverse when in zig-zag stitch. I removed plate and removed all threads jammed in there. It starts out rough, not running smoothly then jams
Riding Lawnmower Fluid Leaking?What causes gas and oil to come out of the air line and pours out all on the air filter when it starts and runs then the fluid shoots out of the air line going to air filter?
Changing Stitching Pattern?How do I change the zigzag stitch to normal stitch?
Troubleshooting a Simplicity Sewing Machine?I have a Simplicity sewing machine, made in the 1980s. It works fine sometimes, but often it goes crazy. I hold the pedal about halfway down, and the speed changes drastically (super fast to super slow to fast to slow, to a dead stop, then starting again).
Snapper Riding Mower Keeps Dying?If your riding mower's engine is not operating correctly, there are a few things to check before bringing it in for service. It may be a problem with the carburetor, the filter or the lines may need to be cleaned.
Tension Dial Not Working on Brother Sewing Machine?The tension dial on my Brother sewing machine doesn't seem to make a difference with the tension when I turn the dial. Any ideals of what the problem could be?
Determining Two-cycle Mixed Gas from Regular GasolineTwo-cycle mixed gas is generally used for small engines, like yard trimmers or lawn mowers. It is important not to mix up regular gasoline with this blend as it can cause damage to the engine if the wrong type is used. Be sure to refer to your owner's manual for the correct gas requirement.
Butterick EB6100 Sewing Machine Stuck in ReverseMy machine is stuck in reverse and I've been advised to 'reboot' it. However I don't know how to do this. Can anyone help please?
Singer Sewing Machine Hand Wheel Sticks?I own an old Kenmore model 33 sewing machine that I have used for many years. When stitching, the hand wheel will rotate 3 or 4 times when pressing on the foot pedal and then it gets stuck. I can forcefully rotate the hand wheel and get it to sew again, but must repeat the forceful turning of the hand wheel after a few rotations. Can anyone suggest repairs or recommend a repair service in Maine?
Bypassing the Clutch Switch on a Yardworks Mower?I have removed the 5 wires from the clutch bypass of my 2007 Yardworks 42 inch lawnmower. Which wires do I join together now to bypass the switch?
Riding Mower Won't Start?Why won't my riding mower turn over or start?
Presser Foot on Singer Won't Move?How do I repair the presser foot on my Singer 360? It does not move when I flip the lever down.
Troubleshooting a Riding LawnmowerDetermining why your riding mower won't start, constantly stalls, or how to repair other mechanical issues can sometimes be a matter of trial and error. There are many suggestions to help you track down the problem and make the necessary repairs on this page.
Finding Replacement Parts for a Kenmore Sewing Machine?Finding replacement parts for your Kenmore sewing machine usually means a bit of time researching on the internet. The older the machine, the more difficult this task may become. The model name, number, and serial number will probably help identify the machine and make your search more productive.
Adjusting the Needle Alignment on a Singer Sewing Machine?I have a Singer 8019 model sewing machine. I need to fix the needle alinement to the center. How can I do that?
Sewing Machine Runs Without Foot Pedal?If your sewing machine runs as soon as it is turned on, before pressing the foot pedal, there are two possible culprits. One is the pedal itself. I new one may correct the problem. There may also be an issue with the connector on the machine. Generally speaking if a new pedal does not fix the problem it may be time for a repair shop visit.
Sewing Machine Stitches Too Loose?It is very frustrating to have your machine making stitches that are too loose. Typically this can be corrected by resetting the tension. For other ideas to help correct this issue read on.
Adjusting the Needle Position on a Kenmore Sewing Machine?If your needle is not in the center position, first check to see if it moves at all to any other position. If not then it may require cleaning or repair. You can do that yourself or take it in to a sewing machine service provider. Read on for some helpful links.
Repairing a Brother Sewing MachineSome sewing machine repairs are easy enough for the owner to make themselves. Others may require taking it in for repairs. This page contains some information about repairing a Brother sewing machine.
Sewing Machine Not Getting Power?The light on my sewing machine doesn't glow when I plug in the speed controller and there is not any movement in the machine to be seen at all. So I am wondering if it's the machine or the speed paddler that isn't working! Please suggest what to do?
Mini Sewing Machine Not Stitching?These mini machines are notorious for having issues, but that aside like a full sized machine, you will need to do some troubleshooting to see if you can determine the cause of the malfunction. If that fails, check for videos or manufacturer's guides online.
Unable to Change Stitch Length on Sewing Machine?It is extremely frustrating when you are unable to change the stitch length on your sewing machine. If there is no fix in your owner's manual, it is likely time to take it in to a repair shop.
Cleaning an Old Singer Sewing Machine?Cleaning an older Singer sewing machine will help keep it in good working order. If you do not have a manual describing the best process for your model, you might research it on the net. Oiling is often done at the same time.
Feed Dogs Won't Go Down?I have a Frister Rossmann 906 sewing machine from the 1970s. I can't get the feed dogs to go down. The switch and I guess the levers are stuck, but I don't see any way to access the levers. I'm using it for machine embroidery, but it would be better without the feed dogs. It is in perfect working order otherwise. I wish you could get good machine diagrams with purchases.
Sharpening Folbate Reel Mower Blades?How do I sharpen Folbate mower blades? It is a m3 model Queen.
Presser Foot Not Connected on Euro-prox Machine?I have a Shark Euro-prox sewing machine model 8260 whose pressure foot seems not connected. Does anyone know anything about this type of sewing machine? It was given to me and I'd really like to use it if possible.
Empisal Overlocker Is Not Stitching?My Empisal overlocker's foot is not moving. It makes the noise but no movement. I've been unemployed for more than a year, I'm 55 and I'm single. I am doing needlework for an income till I find a job. I can't afford to take it in for repairs I barely make enough to survive. Can I fix it myself?
Repairing Foot Pedal on a Baycrest Sewing Machine?I have an old Baycrest sewing machine and there are 2 wires leading to the foot pedal that are supposed to be attached in little black electrical box but one of them is off and I can't tell where it should reattach. Can you send a picture of where the 4 wires attach in the electrical box leading to the power and the foot petal please?
Tang 15 Needle Embroidery Machine Not Stitching Properly?I have a Tang 15 needle embroidery machine. I have been waiting 9 months for a mechanic to fix it. It sews approximately 30 stitches then stops. I've checked threading and the bobbin, but no luck. The mechanic has my book.
John Deere Tractor Won't Move After Hitting a Stump?I have a LA 105 John Deere tractor. I hit a stump and now the tractor will not move. The tractor engine starts up and runs fine. The mower deck runs fine. It just will not move when in gear.
Steering Wheel on Yard Machine Mower Won't Turn Right?What should I do when my Yard Machine's steering wheel cranks and does not turn to the right.
Toro Riding Mower Won't Start?It is exceedingly frustrating to get set to mow the lawn and have your mower refuse to start. This page addresses the possible reasons why your Toro riding mower won't start.
Repairing a Vintage Singer Sewhandy Toy Machine?How do I repair a faulty stitch regulator on a Singer Toy Sewhandy sewing machine model number 20-10?
Replacement Part for a Pfaff Sewing Machine?What is the black, round disk about 2 1/2" in diameter called in the Pfaff 0100A (lavender) sewing machine? It broke and we need to find it. Also there is a pin that fits into it?
Repairing a Tailor Sewing Machine?I was replacing the upper tension on a Tailor 935 FA, how do I put it back together?
Sewing Soft Leather on a Brother Industrial Machine?I have been sewing cotton materials and even denim materials all with excellent stitch quality. I have now selected quite soft leather to sew and can't produce a stitch. The material feeds through the machine in the usual way, but only makes holes. I have tried various tensions that do not make any difference. When I revert to the cotton fabric hey presto all is good - help!
Broken Reverse Lever on Singer Concerto 3?I was using my Singer Concerto 3 today and when I pulled the lever to reverse stitch to finish off, it broke. I need help on how to get into the machine. I unscrewed the screws at the top of the machine and nothing happened.
Connecting Rod Broke on a Craftsman LT2000 Riding Mower?I have a 2014 Craftsman LT2000 riding mower with Platinum 21 HP Briggs and Stratton engine. I can not figure out why the connecting rod broke. It had oil. I am being told it's due to lack of lubrication.
John Deere 125a Won't Start?I have an 2006 John Deere 0125a riding mower that powered down while mowing. I noticed the oil drain tube was gone. We got a plug and refilled the oil and could not get mower to start. We replaced the fuel filter and the 2 armatures as well as new plugs and still can't get it to run.
Blades Won't Engage on a Troy Bilt Riding Mower?The blades on my Troy Bilt riding mower won't engage.
Repairing an Ariens Riding Mower?Ariens is a highly respected manufacturer of lawnmowers and other yard equipment. Small repairs can often be done at home while other issues should be taken to a business specializing in small engine repair.
Replacement Parts for a New Home Sewing Machine?I have a New Home Light Running sewing machine. I am missing a bobbin winder thread guide. Where I can buy it?
Reattaching the Hand Wheel on a Singer Sewing Machine?I have a Singer One Plus and the hand wheel fell off. I just need to know how to line it up to get it back on. I have all the parts.
Repairing a Singer Touch and Sew 625?A few weeks ago I found and old desk at a thrift store, thinking it would be good for crafts. Well, yes, and there was a surprise sewing machine inside! The motor works and the bobbin area doesn't seem to be clogged up with debris, but the hand wheel is jammed and it smells a little musty. It looks like a very old model and I'm not sure how to fix it.
Instruction Manual for Nelco Sewing Machine?These vintage sewing machines were manufactured in Japan and are still popular today with collectors. This page contains information for finding an instruction manual for a Nelco sewing machine.
Murray Riding Mower Won't Start?I have a Murray riding mower 425155X92B. It will turn over, but not start. It does have a new battery.
16 HP Briggs and Stratton Engine Won't StartThe problem may be the starter or the alternator if your engine will not crank over fast enough to start. This is a page about 16 hp Briggs and Stratton engine won't start.
Changing the Sensor on a Singer Futura Embroidery Machine?I need to change the sensor on my Singer Futura embroidery unit that holds my hoops. Can I take the whole bar off or do just the sensors come off?
Butterick Sewing Machine Only Runs In Reverse?I received my Butterick EB6100 sewing machine yesterday and set it all up. Then I tried a test run, it only runs in reverse. How do I reset it? Could it be the stitch settings?
Cleaning the Thread Tension Regulator on a Toyota 5000?This machine, a Toyota 5000, is 40 years old. The lower thread underneath the fabric is bunching up a lot. I understand this is to do with the threading and tension of the upper thread. I have noticed for a little while that the thread tension regulator is behaving inconsistently. How I clean it?
Sewing Machine Not Picking Up Bobbin Thread?Today I was sewing and I noticed my machine wasn't making the bottom threads. I changed the needle, thread, and bobbin and then I realized that the black plastic part that holds my bobbin isn't spinning with the outer silver rim that is spinning making the thread not catch when I try to thread the needle.
Sewing Machine Not Catching Bobbin Thread?I have a vintage Athena 2000 electronic sewing machine. The issue I have is that whenever the thread on the needle of the machine tries to grab for the bobbin thread every time I give it a full rotation the thread on the needle constantly stops halfway and does not make the full rotation to the bobbin thread.
Repairing a Broken Tension Knob on a Kenmore 158 Sewing Machine?When my Kenmore 158 arrived, the tension knob had been snapped right off in shipping. I can put the knob back on, but it does not stay in place. There is no set screw for this model. It looks like there was a little tube that held the pin that broke. Can this be fixed or is the machine a total loss?
Repairing the Blade Release Switch on a John Deere Mower?If the blade on your riding mower will not release, you have a problem that may be repairable without a trip to a mower repair shop. There are several suggestions contained in this page that can assist you in repairing the blade release switch on a John Deere mower.
Janome Memory Craft 7500 Sensor Foot Error Message?My Memory Craft 7500 is displaying a message that says "sensor foot check mode". What does that mean and how can I correct it?
Embroidery Machine Will Not Pick Up Bottom Thread?Just as with your typical sewing machine there are two thread sources that work together to create the designs. This page offers some suggestions for what you can do if your embroidery machine will not pick up bottom thread.
John Deere L100 Won't Start?My John Deere L100 will turn over, but will not start. It has a new battery.
Trouble With Sewing Machine After Bending NeedleSometimes when you accidentally bend a sewing machine needle you can throw the timing out of adjustment. This will probably require a trip to a repair shop to have it corrected. This is a page about trouble with a sewing machine after bending the needle.
Brother Innovis 955 Will Not Do Fill Embroidery?Why wont my Brother Innovis 955 do fill embroidery? The machine has recently been used for fill text, but for some reason it won't do it now.
Bobbin Thread is Bunching UpAdjusting the tension on your sewing machine can usually fix the problem of bunched bobbin thread. This is a page about bobbin thread is bunching up.
John Deere LX277 Is Running Slowly?There are a few possible issues that might cause your mower engine to run sluggishly. Check out the suggestions found in this page about John Deere LX277 is running slowly.
Craftsman Riding Mower Battery Won't Stay Charged?My Craftsman, model 917273022, lawn tractor's battery drains while cutting the grass. I have to recharge the battery to restart. I replaced the stator and still have the same problem.
Replacement Parts for Good Housekeeper Sewing Machines?Finding replacement parts for a vintage sewing machine will require some research. Checking the internet for the different suppliers that carry parts for older machines is your first job. This is a page about finding replacement parts for a Good Housekeeper sewing machine.
Riding Mower Won't Restart After Hitting Something?The impact of hitting or running over something with your riding mower may cause damage to the flywheel key, keeping you from restarting the mower. This part can be purchased and replaced to get your mower back up and running. This is a page about what to do when your riding mower won't restart after hitting something.
Brand New John Deere E130 Won''t Start?I just had it delivered and mowed for 30 minutes. I went over some tall grass and it shut off. I cleaned the grass from the blades. Now the machine won't start or even try to turn over. I checked the contacts for the battery and spark plug. No ideas.
Reverse and Needle Down Button Not Working on Silver Sewing Machine?I have a Silver 1080 sewing machine. When I press the button for reverse it won't work. Neither will the button for needle down position.
John Deere L110 Mower Won't Start?I can turn the mower from the top, but it will only turn so far then it stops like it's hitting something. It was mowing great then it just stopped. I have never had any trouble out of it. I was told this model was bad about the piston pin coming out and the piston not moving so it won't start or move any more.
Installing a New Solenoid on Mower?If your lawn mower won't engage and turn over to start, you may need to replace the solenoid. This is a page about installing a new solenoid on mower.
Value of a 1920 Singer Sewing Machine?I would like to determine the value of an antique 1920 Singer sewing machine that needs restoration. Where do I go to get it restored in St. Louis. MO or where can I sell it. It has the foot peddle.
Repairing a Leaky Carpet Shampooer?If your carpet shampooer has a leak, you will need to repair it or you will have a mess instead of clean carpets. This is a page about repairing a leaky carpet shampooer.
Sewing Machine Wheel Won't Move?If your sewing machine well is stuck and will not move, it may be time to take it in for repair. This is a page about sewing machine wheel won't move.
Remington String Trimmer Has No Tension?I have a 22" Remington string trimmer. I went to try to start the trimmer, pulled back the control bar and suddenly no tension on it. Anybody know how to fix?
Simplicity Model SL 415 Sewing Machine Not Stitching?I have a Simplicity model SL415 sewing machine. I have had it for maybe 25 years and never had problems. Last week I was sewing and the stitches would skip and maybe do a stretch stitch. Today I started and it won't pick up the thread to make a stitch. I've cleaned it, oiled it, and changed the tension, but it will not stitch.
Sewing Machine Needle Won't Seat Properly?What could be the cause if my needle will not properly seat in the holder with the flat side to the back of my sewing machine?
Repairing a Broken Bobbin Case for a Pfaff Machine?The spring that holds the little lever on the bobbin popped out. I have no idea how to reassemble this. My machine is a Pfaff German model Varimatic 6091 purchased in 1999.
Broken Needle Stuck in Needle Bar?I have Singer model 2662 with a broken needle top stuck in the needle bar. To make matters worse, it has fallen sideways in the bar! I have tried several things to get it out, a magnet, screwdriver, needle nose pliers and it seems to be jammed in there to where I can't insert a new needle.
Craftsman Riding Mower Smoking and Burning Oil?I have a Craftsman LT2000 riding mower. I received it last year from my grandfather. The mower was burning oil so I replaced the head gasket and tuned it up. The mower continued to burn oil and smoke lightly. This year the smoke has been really noticeable and it is burning 40z of oil or more per hour.
Motor Pulley Moves on Singer 513 Stylist?I have a Singer 513 Stylist. Recently the motor pulley started pulling away from the motor during operation. I simply push it back in and the machine continues until the pulley pulls away from the motor again. What can I use to keep the pulley from pulling away?
MTD Riding Mower Won't Start?My MTD 42" riding mower quit after 15 minutes and will not fire to start. Could it be an inline fuse? It's like the battery is dead, but it's not, it won't engage starter.
Do It Yourself Mechanical RepairsThis is a page about do it yourself mechanical repairs. Many times there are simple things a person can do to either repair or extend the longevity of a an appliances or piece of equipment, using common household items. Be your own MacGyver and save some money by fixing it yourself.
Repairing a Singer 457 Stitch Regulator Lever?If the stitch regulator on your sewing machine is malfunctioning it may be impossible to maintain a consistent stitch length. This is a page about repairing a Singer 457 stitch regulator lever.
Lawn Mower Revs Up and Down Until Blades Engaged?My lawn mower speeds up and down until I engage the blades. What is causing this to happen?
Sewing Machine Constantly Runs When Turned On?There must be a short somewhere if your machine is not being controlled by the foot pedal. Time to consult a professional. This is a page about sewing machine constantly runs when plugged in.
Whirlpool Washer Not Spinning Properly?A washing machine must be level and the load balanced to spin properly. Otherwise it may be time for a repair. This is a page about whirlpool washer not spinning.
Mower With a Briggs & Stratton Engine Won't StartThis is a page about diagnosing a mower with a Briggs and Stratton engine that won't start. Before you take your mower to a repair shop, here are some possibilities to look into. Diagnosing the issue yourself can save you time and money, so its worth a try.
Nelco Sewing Machine Jamming in Bobbin Area?Try removing the bobbin and the needle plate from the machine. Clean all the dust and pieces of thread in the bobbin area completely. This is a page about Nelco sewing machine jamming in bobbin area.
Mower Battery Hooked Up to Wrong Terminals?Mistakes happen and hooking up battery cables on your mower to the wrong terminals is unfortunate, but possible. This is a page about what to do if you hooked up your mower battery to the wrong terminals.
Having an Antique Sewing Machine Repaired?I have a 1874 Domestic sewing machine. Where can I go to get it repaired? I would like to also know what it is worth, just curiosity, not selling.
Lawn Tractor Won't Start After Hitting a Stump?I hit a stump with my John Deer lawn tractor. It immediately stopped. I moved the tractor and now it will turn over and act like it wants to start, but no luck. What should I do to repair it?
Husqvarna Mower Won't Start When Hot?I have a Husqvarna zero turn mower, it starts great when cold, after it warms up it will not turn over. I can jump the solenoid and it will start and run fine, any suggestions?
Troybilt Engine Exhaust Blowing White Smoke and Oil?This year my 2008 Troybilt Pony mower took about 6 times trying to start before it finally caught. Then it started blowing thick white smoke. I let it run for 3 minutes to clear, but it got worse and spit a lot of black oil out of the exhaust. I shut-off immediately.
Repairing a Mini Sewing Machine?My mini sewing machine is not working properly.
Sewing Machine Keeps Jamming?The bobbin being loaded improperly may make your sewing machine jam up. This is a page about sewing machine keeps jamming.
Needle Getting Stuck in Bobbin Shuttle?When the needle continually gets stuck in the bobbin shuttle it is time to repair your machine. The timing may be off. You can try to find a repair video or take it in to the shop. This is a page about the needle getting stuck in bobbin shuttle.
Wiring the Foot Pedal on a Morse Sewing Machine?When replacing or adding an electric foot pedal to an older sewing machine, you will often find help by searching for a YouTube video for your model. This is a page about wiring the foot pedal on a Morse sewing machine.
Replacement Pattern Selector Dial for Sierra Sewing Machine?I'm looking for a pattern selector dial for a Sierra 234F sewing machine.
Janome Machine Not Picking Up Bobbin Thread?There are a few things that can cause this problem. Try checking the manual or manufacturer's website. If all else fails it is time for a trip to the repair shop. This is a page about Janome machine not picking up bobbin thread.
Singer Sewing Machine Not Picking Up Bobbin Thread?If you have pulled your threads properly, it may be a worn bobbin gear when your machine is not picking up the bobbin thread. This is a page about Singer sewing machine not picking up bobbin thread.
Removing the Rear Wheel on a Troy-Bilt Mower?This is a page about removing the rear wheel on a Troy-Bilt mower. When making repairs to your lawn mower, you may need to check out the many videos on YouTube if you don't have a manual that contains repair help.
Replacing a Sewing Machine Fuse?This is a page about replacing a sewing machine fuse. Your manual should provide the information on how to do the replacement. If you do not have a manual, check online by manufacturer. You should be able to find the instructions and very likely a downloadable manual as well.
