social

Sewing Machine is Breaking or Bending Needles

August 11, 2011

closeup of sewing machine foot and needleIf your sewing machine has begun to bend or break needles there are several possible causes. The following list will help provide some ideas for troubleshooting the problem with your machine.

    Advertisement

  1. The needle is improperly inserted.
  2. The needle is bent or blunt.
  3. The needle clamp screw is loose.
  4. The needle thread tension is too tight.
  5. The bobbin cartridge is in upside down.
  6. The user is pulling too tightly on the fabric while sewing.
  7. The needle is too fine for the fabric being sewn.

If after checking these possibilities and making the appropriate corrections as needed, your sewing machine continues to break or bend the needle, it may be time to take it in for repairs.

 
Read More Comments

April 9, 2012

Clean and oil the machine per manufacturer directions and make sure throat plate is properly aligned.

 
Read More...

November 4, 2019

I have threaded my needle more than 10 times and it keeps breaking. I have broken like about 4 needles and all the bits fell into the machine how can I get it out?

Does this affect my sewing? I am frustrated and tired; what should I do?

Answers


Bronze Post Medal for All Time! 105 Posts
November 4, 20191 found this helpful
Best Answer

Normally if a needle is breaking it could be the way the needle is inserted into the machine. Also there is an issue with the needle hittle the bobbin inside the machine that can cause it to break.

Advertisement

If you need to remove the pieces of needles from your machine use a screwdriver and remove the plate. Here you can get out the lint and clean the machine. This could help the needle from breaking if you make sure it is installed correctly and it is not hitting the bobbin when it moves up and down.

 

Diamond Post Medal for All Time! 1,246 Posts
November 5, 20190 found this helpful
Best Answer

I used to have that issue when I first started out and it was that I had threaded the machine wrong and it was pulling on it, causing it to hit the plate

 
Answer this Question

March 25, 2015

A piece of broken needle is stuck in my antique sewing machine. I tried everything, Blaster penetration, pushing with a needle, pushing with a fine screw, and nothing works.


Please advise if you have experienced this.

By Chabeyline

Answers

Anonymous
December 5, 20161 found this helpful
Best Answer

I took a broken needle out with a magnet

 
Answer this Question

October 17, 2005

My sewing machine needs adjustment but I don't know how and I can't afford to take it to a repair shop. The needle keeps hitting and breaking or bending really bad on the feed dog. Does anyone know how and what to adjust so the needle is in time with the feed plate. (The little teeth like things that help pull the material under the needle). Thanks to anyone who can help with this.



Brenda from Somerville, AL

Answers

By Memere (Guest Post)
October 17, 20050 found this helpful

Sorry, but your machine needs a professional adjustment. Do not continue to use your machine untill you have it repaired.....you could do more serious damage to it.

Advertisement

A new machine would be more costly than repairing yours. Get a free (or low cost) estimate, then save your pennies. It might be less expensive than you think.

 
By Cindy in AL (Guest Post)
October 18, 20050 found this helpful

Make sure the needle is pushed all the way in the holder for it.
I had to have mine fixed once because it did not reverse. They did a cleaning and that fixed it. It only cost $40. I did get a recommendation from a sewing shop, tailor, as to wear to go for repairs. I used the person's name who refered me, if that made a diffence to the repairman.

 

Silver Post Medal for All Time! 364 Posts
October 18, 20050 found this helpful

That can happen when the needle gets too old. Replace the needle with a new one. This action solved the problem for me (because it's what I was told to do at sewing class years ago).

 
By Brenda (Guest Post)
October 18, 20050 found this helpful

Thanks Cookwie, but I have replaced the needle with new ones but that is not the problem. The needle hits the plate when it goes down. I made sure I had the right needle for my machine and made sure it was inserted properly. I guess I will just have to take Memere's advice and save my pennies so I can take it to a repair shop.

Advertisement

Being disabled, it takes a while to save those pennies though and I was really hoping to sew some things for my granddaughters for Christmas. Thanks also to Cindy in AL. and to Memere for taking the time to help. God Bless you all.

 
October 18, 20050 found this helpful

You may simply have the wrong type of needles in your machine.Did you check the manual?

Other possible reasons may be:

As stated above - bent needle or needle inserted improperly (or crappy needles)

Plate is loose or crooked

Too much upper thread tension - or thread is caught elsewhere & not coming off spool properly - check threading

Too much bobbin tension - or bobbin is in backwards or upside-down

Advertisement

Thread is too thick

Fabric is too thick for needle

If you haven't trouble-shot all this stuff yet, check it out.

HTH

 
October 18, 20050 found this helpful

Oh and..

is it a zigzag machine? Did you doublecheck to see that needle position is set properly for the stitch you are doing?

 
By jeanette (Guest Post)
October 19, 20050 found this helpful

Memere are you from louisiana???

 
By James (Guest Post)
January 6, 20070 found this helpful

Brenda, the feed dogs on your machine maybe have come loose. I see this a lot. Check the screws in them. If not the needle bar or feed dogs, one have jumped time not that big of a deal oh by the way I also live in Somerville Al

 
By Brenda from Somerville, AL (Guest Post)
January 7, 20070 found this helpful

Thank you James. I will be sure to do what you suggested. I put my sewing machine away and have not used it since I posted the first time. I tried all the suggestions from others but none of them worked.

Advertisement

By the way, you can contact me at brenest(at)aol(dot)com (replace (at) with @ and (dot) with . ) I can explain this a little better in email. Thanks again, Brenda

 

Silver Feedback Medal for All Time! 270 Feedbacks
February 29, 20121 found this helpful

Please remember, all sewing machines need a good maintenance check up. The more computerized the more specialized the repair person.

I had been having an issue with my 25 year old machine and finally treated it massively. I had been doing my proper oil, cleaning, etc and blowing it clean with the air compressor from garage.

So I decided to buy a new one. Pfaff with utility sewing - not fancy. And when I brought my new one in the house, my old one worked perfectly after that. Karma?

Took my old machine to the shop of my new one and for $50 they went through it, tightened up, adjusted this and that, and now I have 2 machines to love.

Since they don't make machines like they did back when the Kenmore was new, I appreciate keeping it running. I paid $700 back then for the machine. Bells and whistles but nothing electronic. So I expect another 25 years with proper care.

Don't abuse it. Don't mess with the tension unless you know what you are doing. I keep notes besides the machine if making adjustments. Don't use cheap thread, match up thread with fabrics, and my rule of thumb I don't let anyone use it unless I can verify they know what they are doing. And it does not leave my house.

My husband has his sets in the basement for repairs of jeans, tarps, etc. On clean up day- where you can set things out to trash - one week a year - his seamstress got a new fancy one and set 2 good old machines out, stickers from there 'rehab in the shop' on them. I picked them both up. So we had 4 machines in the basement. Had another elderly friend who kept borrowing the simple one so her sister with dementia could use it - sew quilt squares. The last time she borrowed it I told her it was not to come back. It was hers.

 
Answer this Question

May 8, 2014

sewing machineI have a Super Flairmatic 190B sewing machine. It has been working great then all of a sudden the needles keep breaking when I put it in reverse. I think the needles I have now are cheap, but it was doing it before I bought them. I have gone through over 30 needles in the past few weeks.

I have been told by the sewing center that it may be the timing, but I could fix it myself if I had a video that would show me. Would anyone on here have a video that shows how to set the timing on a front loading bobbin? I have done this before on an industrial machine, but can't find one for this machine. Please help I am cheap and don't want to spend the money to take it to a repair man. Thank you.

By pyduke

Read More Answers

August 18, 2013

I have only just bought this machine, so I was really disappointed to hear it start clanking and jamming. It was a bit scary. I tried everything to correct the threads, but there doesn't seem to be a problem with the threading or any thread caught in the bobbin area underneath. I changed the needle afterwards and it seemed to work perfectly again for a few minutes.

Then the needle broke :( This has happened another two times. I don't know what's wrong. Do I just return the whole thing? It seems such a shame. I hope somebody can give me a hand on here? I would much rather know it's me messing things up rather than the machine being broken.

By Becky

Answers


Silver Feedback Medal for All Time! 282 Feedbacks
August 25, 20130 found this helpful

Your problem could be caused by one of two issues. First one is incorrect bobbin case seating. Your machine is a front load bobbin system and getting that removable case properly seated can be a real beast of a job!

In stitching, the needle goes down into the bobbin case as it rotates, catches the bobbin thread and loops to create the stitch. If the bobbin case is not in there correctly it will cause needle breaks because the needle smacks against the case that isn't rotating correctly.

Those front load (and side load) bobbin systems are very difficult to use! I try to steer my sewing students to machines that have the nearly jam proof top drop-in system because the frustration with the front or side load system is too great - it can put a sewer right off sewing!

If you bought the machine at a dealer or a fabric store like JoAnn or Hancock's, take the machine back to the store and ask one of the staff to help you learn to load the bobbin case correctly. There should be no charge because you bought the machine there.

Take notes; if you can record the session you can play back the audio whilst trying to load the case at home. Snap several photos with either a mobile phone or a digital camera because yes, a picture really can be worth a thousand words when you are struggling to correctly seat one of those bobbin cases!

If you bought it at a big-box like WalMart or Target you're not going to get much help from them, sorry to say because most of the staff in those departments are not sewers. They used to be but they aren't anymore. You can try taking the machine to a Singer dealer, or JoAnn, etc, but expect they will charge you for teaching you how to use the machine.

The only other thing that could be happening is that the machine was dropped in the warehouse and the timing is off. This is a warranty problem for a qualified repair tech to fix, it isn't something you can do at home.

If you still have the receipt you can exchange the machine for either a replacement of the same model, or look for one that has the top drop-in system (so much easier! You may have to pay a little more but it is SO worth it! Any Singer or Brother top drop-in machine will give you years of sewing satisfaction).

When choosing the replacement box, make sure there are no crushed or dented corners as a sign the box was handled carefully. You may even want to try the machine before leaving the store with it.

 
Answer this Question

July 1, 2013

My Dressmaker 300z sewing machine needle strikes the metal piece below the bobbin case and breaks the tip of the needle off. It was bought in 1990 at Walmart. How can I fix it?

By Melba M.

Answers


Silver Feedback Medal for All Time! 282 Feedbacks
July 2, 20130 found this helpful

The timing is off in the machine-you need to take it to a professional for a resetting of the timing. This really isn't something that can be done at home by the sewer.

Most repair techs will have access to the information (usually in a service manual, a pricey item that can cost as much as several hundred dollars US) needed to set the timing on the different models of majour manufacturers, including your particular machine.

Make sure when you take the machine in that you get an estimate, and that the estimate includes a servicing (cleaning, oiling, and checking everything is in good order).

 
Answer this Question

November 11, 2010

My sewing machine froze up when I pressed the foot pedal to make it go. The needle doesn't do up and down. I can't even turn it to go up and down.

 
Read More...

January 16, 2015

My industrial sewing machine is breaking needles on reversing. I am staying in Africa, I depend on you.

By Desi

Answer this Question
<< First< Previous
Categories
Home and Garden Repair Machines Sewing MachinesJuly 7, 2011
Pages
More
👒
Mother's Day Ideas!
🌻
Gardening
🐰
Easter Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-03-28 02:36:51 in 7 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf/Repair/Machines/Sewing_Machines/Sewing-Machine-is-Breaking-or-Bending-Needles.html