When I turn on my Hoover Max Extract 60 shampooer, it starts dumping water out of the bottom of the vacuum, it dumps the whole clean water in about a minute. Can anyone help?
My Hoover carpet shampooer is not spraying water but dripping it. Does anyone know how to fix the water/cleaner sprayer?
My Hoover steam vac, F7452-900, All Terrain Spinbrush, is leaking from the solution/water tank. I need to know how to fix it.
I have a Hoover Platinum Max Extract carpet cleaner. I cleaned out the hose nozel by blowing it out with air. When I filled the detergent canister and the water canister and put them back on, both containers started to leak.
They completely leaked out. I cannot figure out what happened or how to fix this problem.My Hoover model number is F5915-905. I was using the cleaner, when the motor suddenly stopped. It won't start back up. I just bought it 5 months ago. Does this model have problems with overheating? I'm really not sure what the problem is.
By JoAnne
If it is only 5 months old, it is likely still on warranty. You should contact the company, by phone or email. You will likely have some sort of customer service info with your paperwork that came with your machine.
How do you repair it if it is leaking water after you sit clean water tank back on machine? How do you get to top hoses?
My Hoover carpet cleaner will not turn on. I used it about 2 months ago and it ran fine; turned off and on fine. I went to turn it on today and nothing.
I checked the outlet, cord, etc. Any ideas what it may be besides probably junk?I took apart a Hoover 2 tank system carpet cleaner because it made an awful noise and smelled like smoke. Now I'm trying to put it back together and can't remember where the little hoses go under the hood to the pump.
I have the Hoover Power brush. The motor runs when I hit the switch, but when I pull the button no water circulates through the suction part. The roller is rolling and where it sucks it's sucking, but the water doesn't go down on the floor.
No water comes out of my attachments and the water hose is not clogged. All the water goes into dirty water tank. I have a Hoover Extra 77.
By Leslie from Fort Dodge, IA
My Hoover CleanJet is leaking water as soon as I fill it. Does anyone have advice on fixing it please?
My Hoover Spinscrub steamVac cleaner just started leaking water from the bottom. Even when my lever was not off (not squirting water) the water was still leaking from the device. When I was drying the carpet with the vacuum, it was still squirting water (which made drying it useless).
Can you please let me know what I can do to fix this?
I have a Hoover Power Scrub SpinScrub 50. Clean water will not release from the tank because a very small plastic poker that releases the water broke off The poker is not part of the water tank, but is on the plastic stand just below it surrounded by a rubber ring a little larger than a quarter.
Please let me know how to replace it or the nearest repair shop in area code 32218.
Thanks.
My puppy chewed up the cord on my Hoover carpet shampooer. Can you help me with how to get a replacement?
My shampooer is not spraying shampoo on to the carpet. I pull the trigger on the handle and nothing happens. How would you fix a problem like this?
By Harold
How do I reattach the cleaning access latch?
It sounds like your latch could be broken and therefore it is hard for you to attach it back on the cleaner. I would suggest that you order a new part to make it easier to put it back together.
It sounds like your latch may be broken but difficult to know unless you know that it 'broke off'.
You might want to be sure that you can install a new latch.
Contact your local Sears Service Center and explain what happened to them and they can tell you if you need a new latch. They also have parts and their parts usually include instructions on installation.
www.service-center-locator.com/
You can also ask questions or order parts on several sites:
www.repairclinic.com/
You may need a manual but model number will be necessary:
I have a Hoover Spin Scrub 50. Water is leaking from the water/solution tank. How do I replace the grommet on the outside where the water tank sits and get the stick, the spring, and the grommet back inside the water tank?
This is pretty handy to do. First make sure that your cleaner is unplugged, and there is no solution in the container and it dry
Check this link to watch the video and also look photos using pause
It could be a problem with the water base assembly or the filter in the machine. If the filter is not pushed all the way up this can cause the water to leak. Check the pump assembly and make sure the hose is not cracked or leaking. If it is you should order a new one.
I've had my machine for a year or better. I went to use it one day and the roller wouldn't roll and made this loud noise. It wasn't cleaning my carpet. We took it apart to check the belt and the belt is OK. So what could be the problem? I paid too much to just let it go.
Help me please.