social

Installing a Sink

Dennis Fitter
May 14, 2006

Installing a SinkReplacing a sink in your home is a fairly quick and easy job.

  1. Look for a new sink roughly the same size as you are replacing so you will not have to change the size of the countertop cut-out.
    Advertisement

  2. Check under your sink and if you see water shut off valves on the hot and cold lines running to the faucet, you're in luck. Just turn them to the off position and you're ready to go to work. If there isn't a shut off present, you'll need to shut off all the water lines in the house. Save a few pitchers of water first. You can find the main shut-off valve at the water meter. Turn this off, then open all faucets through-out the house to drain the lines. Miss this step and the water sitting in the lines will be draining into the work area.

  3. Using channel lock pliers, undo the connection to the faucet. While you are under there, open the pliers wider and loosen the ring that connects the sink drain tail pipe to the drain trap. The trap is that u shaped, plastic thing.

  4. Lift out the old sink and faucet. It could be stuck down, in which case a pry tool might be required. Kitchen sinks are held in place by a series of clamps you will see by looking up underneath, around the edge of the countertop cutout. Loosen these off to remove a kitchen sink.
    Advertisement

  5. Clean the goop and gunk buildup from the countertop.

  6. Most new sinks come packaged with a new tail pipe and assembly instructions. Do the assembly before setting the sink in place. Some sinks come with a rubber gasket that makes a water resistant seal of the sink to the countertop, already in place. If there isn't a ring, put a heavy bead of latex caulk on the countertop to stop water from leaking in under. Now, simply set the sink in place. Installing a Sink

  7. Next, remove the faucet from the old sink, clean up the mounting base, attach a new set of flex hose water lines, then set the faucet in place. Tighten it down from the underside using the ring nuts removed from the original installation. For a kitchen sink, remember to affix the hold down clamps to the under side of the sink. Join the tail pipe to the drain line by hand tightening the slip ring on that u shaped plastic thing, and everything is set to go.
    Advertisement

  8. With all the faucets open, turn the water on, leaving it to run until all air has been forced out and water runs smoothly. Close the faucets and the job is finished. Oh, don't forget to wash your hands.
     

February 6, 2009

I want to install an undermount kitchen sink. My current sink is on the top. Do I need to replace my countertops as well?

Susan from Yuma, AZ

Answers

By frugal parent (Guest Post)
February 7, 20090 found this helpful

You will have to see what kind of condition your countertop is in underneath the old sink. You should be able to mount it under your old counter.

Advertisement

You could go to your local hardware store and ask someone there or go online under some do it yourself websites.

 
February 7, 20090 found this helpful

When your old countertop was originally created, a hole was cut to put the sink into, and it is likely that the vertical surfaces would not have been finished. They're likely to be rough (plywood showing).

 
February 8, 20090 found this helpful

You will have to install a new counter top too. The edges of the counter top where the sink is set in will not be finished. The edges will be wood so when you put the sink underneath your counter you will see the wooden edge.

Advertisement

I don't know about marble or granite tops, but laminate or ceramic will have a wood base.

 
By (Guest Post)
February 9, 20090 found this helpful

PICO is correct. I am having the same problem going from a drop in to an under mount. Unfortunately my laminate counters will have to be replaced but we don't have this expense in our budget. We are thinking of trying to paint and seal the raw cut out edge with some kind of marine spar varnish. This might be something you could try. Be sure to use the marine varnish like they use to seal boat decks and do several coats. We found the sink for a bargain at a yard sale. It's an expensive stainless one that retailed for well over $300 and we got it for $25. It wont be such a deal if we have to spend a lot replacing the counter tops, tho!

 
Answer this Question
<< First< Previous
Categories
Home and Garden Home Improvement PlumbingSeptember 1, 2013
Pages
More
👒
Mother's Day Ideas!
🐰
Easter Ideas!
🌻
Gardening
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-03-28 11:13:13 in 6 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/Installing-a-Sink.html