I have a Maytag Maxima steam x front load washer. I have had to call a repair tech once and it cost $200. In mid cycle it throws e01 and f08 codes, the door will not unlock and there is no power. It just did it again a week after repair. Here is my tip.
I have a Maytag front load washer, model MFW9600SQO. The F02 and SUD codes show up during washing even though I have done the following: Replaced water pump and strainer. Cleaned out behind the door gasket, cleaned out ball on top of drain at the bottom of the washer. Inspected hose from pump to drain pipe for blockage and found none. Identified that water is flowing into and out of washer. I have unplugged the washer overnight. I have run machine without soap 3-4 times.
I can get it to run, but get the FO2 and SUD code towards the end of wash cycle. If I press the off button once and start button twice I can get it to continue to run, but this has to be repeated every 3 minutes or so until the was is done. What do I do now?
By William B.
I copied this answer from a website called fixya.com. Hope this helps.
If it's not draining properly and shows this F02 Code there may be a simple solution. Take the bottom front panel off (it has 3 screws.) There will be an off white circular plastic thing there. Resembles the top to a cannister. Twist it off. There will be a good bit of water if it hasn't drained properly. I put a cookie sheet under it to catch most of the water. Once you completely unscrew the top off hopefully your problem will be right there. Unbelievable... we found 2 socks, a glove, a bead, coins and don't ask me but there was a nail in there as well. I was so happy that we didn't need to pay a repair man.
My Maytag front load washer will not start. It flashes the letter "F" then the number "11".
I have a Maytag Maxima MHW6000XW and it is giving a code of F06 and E02. What does this mean?
What is error code F20?
By Nancy T.
My 3 yr old Maytag HE front load washer displayed an "F" code. i have followed the instructions manual to troubleshoot the problem, like Pause/Off to cancel the cycle. The problem still exists and the door will not open. I have since pulled the plug. Has anyone else had this problem before? My Maytag model # is MFW9800TQ. I would appreciate any feedback.
By rob808 from Thibodaux, LA
My front load Kenmore did that a couple of times and I had to flip the breaker (couldn't reach the plug) to get it to stop. It hasn't done it in a couple of years,,,never did discover the problem but it stopped. Maybe yours will too.
I have replaced the hoses cold and hot, checked inlet valves, cleaned out drain, and cleaned out inside drain hose. I cleared the inside filter and checked the valve inlet hose for holes.
The washer still throws error, 25 minutes into the cycle and we have to drain it. What else could it be?I have a Maytag Bravo MVWX700XW1 washer. What does error code F7 E1 mean and how do I repair it? Thank you.
The door lock light is blinking on my front load Maytag Maxima. This is all it will do. This happened when I forgot to turn the water on. First it had a code blinking that I looked up and it was for the water, so I turned it on and now it is making a humming noise and the door is locked and that is all it will do. The only way to stop it is to unplug it. Does any one know how to fix this problem? I have only had this washer for about a month.
By Jim S
My Maytag Neptune washer is throwing an error code d4. Help?
By Teri from Elyria, OH
Your manual should explain all the error codes. I really got a scare the first time I got an error code on my brand new sewing machine. I looked it up and found out my bottom thread was tangled.
I have a small Maytag washer model: MHWC7500YW. It stopped working during the washing cycle. I have unplugged it and then it works again for 1 or two loads max; and then stops again flashing the F23 error code. What is this and how I can fix it?
Thanks.
My Maytag washer, unknown model number, it is unreadable is showing code Du and then F. It won't unlock. Anybody know what this means?
Thank you.
I have a Maytag Neptune Washer MAH5500BWW. The service cycle displays code PA and h. What are these codes? The washer won't start, the display board works, and it runs a service cycle.
I am in need of some assistance that the kind of folks at Maytag are either unable or unwilling to perform. My washer, three years old, is giving me an error code of 'f6 e1' followed by three rapid beeps. It's part of the 2000 series (the one with only bad reviews on Amazon), model #MHWE201YW00.
I have already swapped out the machine control board at the advice of a local serviceman, and before I light more money on fire I figured the wise sages of the internet could render better assistance than I've received thus far.
Thanks for solving my first world problem.
The code OE comes up. What does it mean?
By Pamela B
