I have a Maytag Maxima steam x front load washer. I have had to call a repair tech once and it cost $200. In mid cycle it throws e01 and f08 codes, the door will not unlock and there is no power. It just did it again a week after repair. Here is my tip.
My Maytag front load washer will not start. It flashes the letter "F" then the number "11".
I am getting the code 5D on my top load washing machine model # mvw8450wq1.
By Linda
I have a Maytag front load washer, model MFW9600SQO. The F02 and SUD codes show up during washing even though I have done the following: Replaced water pump and strainer. Cleaned out behind the door gasket, cleaned out ball on top of drain at the bottom of the washer. Inspected hose from pump to drain pipe for blockage and found none. Identified that water is flowing into and out of washer. I have unplugged the washer overnight. I have run machine without soap 3-4 times.
I can get it to run, but get the FO2 and SUD code towards the end of wash cycle. If I press the off button once and start button twice I can get it to continue to run, but this has to be repeated every 3 minutes or so until the was is done. What do I do now?
By William B.
I copied this answer from a website called fixya.com. Hope this helps.
If it's not draining properly and shows this F02 Code there may be a simple solution. Take the bottom front panel off (it has 3 screws.) There will be an off white circular plastic thing there. Resembles the top to a cannister. Twist it off. There will be a good bit of water if it hasn't drained properly. I put a cookie sheet under it to catch most of the water. Once you completely unscrew the top off hopefully your problem will be right there. Unbelievable... we found 2 socks, a glove, a bead, coins and don't ask me but there was a nail in there as well. I was so happy that we didn't need to pay a repair man.
I have a small Maytag washer model: MHWC7500YW. It stopped working during the washing cycle. I have unplugged it and then it works again for 1 or two loads max; and then stops again flashing the F23 error code. What is this and how I can fix it?
Thanks.
My washer stopped and is blinking F1. It is full of water; what does this mean?
By Susan from Suffield, CT
I found a link which said to press pause/cancel and then restart. If it doesn't work call for service. The link also said that is is a common problem and is the reason for a number of lawsuits.
Here is the link:
answers.yahoo.com/
What does code F51 mean? The washer won't run. It's been fine for several years. It is a model MVWD75OW from 2005.
By Bob
What is error code F20?
By Nancy T.
My Maytag Neptune washer is throwing an error code d4. Help?
By Teri from Elyria, OH
Your manual should explain all the error codes. I really got a scare the first time I got an error code on my brand new sewing machine. I looked it up and found out my bottom thread was tangled.
I have a Maytag Neptune washer. I was washing a small load when the unit stopped with a code ND. There is dirty water in drum. It won't spin or drain.
By John
The User Guide for my Neptune washer suggests checking for a kinked drain hose or a plugged stand pipe if you get error code ND. If you still have problems you could call their customer service line at 1-888-462-9824.
I have a Maytag Maxima MHW6000XW and it is giving a code of F06 and E02. What does this mean?
My 3 yr old Maytag HE front load washer displayed an "F" code. i have followed the instructions manual to troubleshoot the problem, like Pause/Off to cancel the cycle. The problem still exists and the door will not open. I have since pulled the plug. Has anyone else had this problem before? My Maytag model # is MFW9800TQ. I would appreciate any feedback.
By rob808 from Thibodaux, LA
My front load Kenmore did that a couple of times and I had to flip the breaker (couldn't reach the plug) to get it to stop. It hasn't done it in a couple of years,,,never did discover the problem but it stopped. Maybe yours will too.
The user manual for my Maytag Neptune washer does n't have an F code. I would call Maytag at 1-888-462-9824. They will give you the name of an authorized service company to contact or maybe assist you with the reason for the F code..
Thank ya'll for your feedback.
foxrun41 - my Maytag epic's manual page 22 on the troubleshooting did talk about an 'f' code.
glenn's mom - I did flip the breaker as you suggested - but nothin' happens. door still cannot open the door.
since we have bot a 4 yr-extended protection plan from LOWES. I have called for service since Sunday. the technician that was assigned to my district no longer do servicing. now lowes' service plan-people is looking for another technician for my case. I was told that I have to give them a 24-hr time frame to get someone.
The service guy just left. my maytag washer is all better now;). The culprit was a Lucky Bean! My 12 year old son's Lucky BEAN. thought I check all pockets. the service guy found the bean in the bottom drain pipe after removing the bottom panel of the washer. That bean just shut down the whole system due to the washer sensor. Ah well, all's well n good now;)
*the service guy even gave me a bottle of cleaning liquid to clean off the mildew.
I have replaced the hoses cold and hot, checked inlet valves, cleaned out drain, and cleaned out inside drain hose. I cleared the inside filter and checked the valve inlet hose for holes.
The washer still throws error, 25 minutes into the cycle and we have to drain it. What else could it be?I have a Maytag Bravo MVWX700XW1 washer. What does error code F7 E1 mean and how do I repair it? Thank you.