A friend has a Singer 6268 that gets power to it but nothing else happens. How would he fix it?
I can tell you this is a nice electronic machine and if he is not familiar with this type of sewing machine he will probably have a lot of questions and needs to ask people who are familiar with this model.
I'm pretty sure this machine uses a motherboard that occasionally messes up so ask your questions on forums.
He will have to join sites to be able to ask questions.
www.quiltingboard.com/
sewing.patternreview.com/
groups.google.com/
Here is a link to a free manual so start with printing this.
Manual:
www.singer.com/
He is just at a beginning stage so please ask for help and be sure to keep all links to any forum so you can go back when you have further questions.
www.thriftyfun.com/
Machine.html
This is a link to keep in case you have other problems:
www.singer.com/
This is one of the newer electronic machines that run off a motherboard that is programmed to operate the machine. If you can see the power to the display of the machine and you are not getting any reading off the display there could be a reset problem issue. Please check the manual and find the troubleshooting section at the back of the book. Check the instruction on how to manually reset the machine so that it will cycle through again and reset the program card or memory card.
A continuous tone starts whenever we run on the singer 6268 machine. Should we reset it and how is that done? I'm pretty adept at repairs.
My Singer 6268 works great aside from the speed of sewing fluctuating. I am using my darning foot to do free motion quilting and I will press down to start sewing and sometimes it will be fast, or slow, or completely stop without changing the actual speed.
I have tried cleaning out the air hose, but to no avail.I have a Singer machine, model #6268. The timing seems out; the needle is hitting the metal plate.
I bought a Singer 6268 embroidery machine and it works, but not with a cartridge. Can anyone help me find out how to get it to work?
Sometimes it can be frustrating trying to find the control for raising the feed dogs on a new sewing machine. This is a page about raising feed dogs on a Singer 6268 sewing machine.
Loading the bobbin is an important step for setting up any sewing machine. This is a page about how to load the bobbin on a Singer 6268 sewing machine.
Finding these vintage machine embroidery cartridges will likely require some internet searching. This is a page about buying SewWare cartridges for Singer sewing machine #6268.
I replaced the slide plate as one of the springs had come loose. Since receiving the new plate Part No. 313166 and installing it, I cannot get the bobbin to work correctly. At best it stitches, but pulls many strands of thread at the base of the work. Observing it in action it seems that the spring loaded clip that holds the bobbin case in place is stopping the thread from advancing around the bobbin housing.
Are there any adjustments that I can make at home? Or do I need more new parts? I have owned this machine since 1985 or 6.I think your problem is the bobbin class you're using in the machine - the 6268 uses a very specialised bobbin - the Centour II, and while class 66 (and some badly milled 15J or K class) bobbin WILL seem to fit, the use of them WILL cause the very problem that had you replacing the original plate, and your current problem (thread catching on springs).
You need to be sure you're using the Centour II bobbin class, or a bobbin marked specifically for your 6268.
My Singer 6268 will not do stitches 4, 11, or 18. All of the other stitches work fine. The selector buttons for these three stitches are in the same column. How do I repair that column?
First of all, here's a link to the free download of your user guide at the Singer website:
www.singerco.com/
Go through the manual to be sure you've set the width, length, and any other settings needed for the stitches you want to use.
If that doesn't help, you need to take your lovely vintage electronic sewing machine to a factory authorised repair tech. Yes, it may be expensive (I suspect one of the cartridges has failed) but worth it if the parts needed can be sourced.
Be wary if the tech tries to talk you into 'junking' the machine in favour of a 'comparable upgrade'. He/she may be spot-n your machine has sewn it's last stitches 4, 11, or 18, but as you state the machine is still sewing the other stitches, and assuming all else is fine, there is no reason to 'junk' the machine. Upgrades are great but if you're ok with losing three stitches, keep the machine. It's possible the tech is hoping to get your machine (hence my warning to be wary) for parts or to refurb your machine to sell on - sadly, not all repair techs are as nice as we'd like them to be.
I purchased it used, in unknown condition. It only sews in reverse even when the reverse function is not selected. Any help or hope resolving?
By Diane B.
There could be many problems resulting in the machine's current difficulties. If you are interested in keeping the machine, the best plan would be to take the machine to a repair shop. The shop can examine the machine and give you an estimate of the current condition and what can be done to fix the problems (there will probably be an initial exam cost).
My old Singer 6268 machine died. Does anyone know if the problem is the motherboard and if so, where can I purchase a motherboard?
By Clare
If you haven't already, this machine needs the attention of a qualified Singer repair tech. Replacing the motherboard on a computerised machine isn't something that can be done at home, especially on a vintage computerised machine like the 6268.
