My Frigidaire front loader washer is not spinning when full. It spins ok if only a small amount of clothes are in it. We just replaced the belt, but it didn't help the problem. Should I just buy a new one or is this fixable?
We just had a similar problem with our front loader except ours stopped spinning altogether. We couldn't find anyone who wanted to look at it. My husband had already found the belt was not the problem. One repairman suggested he look at the brushes connected to the motor which turned out to be the problem. Apparently they have a little tail which stretches over time (normal wear and tear). Ours had fully stretched and were no longer making the connection required to spin the drum. My husband replaced the brushes and we're up and running (or should I say spinning!) again.
The drum is spun by the belt and motor, with it spinning with a half load I would say that the belt you got was the wrong size (to big) or the spring loaded self adjusting tenisoner isn't working, motors for the most part either work or they don't but it would be worthwhile to spin it by hand and see if it's freely spining, if it isn't it needs to be replaced.
Why is my washer flashing 3E and not spinning? What can I do?
By htisi from Kamloops B.C. Canada
I have a GE front load washer model WBVH5200J1WW. It is pumping but not spinning or turning. I have checked the belt and it is in good shape.
The door is locking as it should; it just won't add water or spin.Your pulley may have to be replaced www.appliance-repair-it.com/
3 days ago my Maytag front loader washer stopped and threw a code. So I looked it up and it turned out the drain behind the front panel was clogged. I fixed it. Well now when the washer is done I go to put the clothes in the dryer and they are soaking wet. So I checked the drain again just to make sure and it's clear. The washer is not throwing a code. Any ideas on what the problem is or could be?
By Chad M.
Once I had a heavy blanket in with the rest of the clothing. It stopped the machine from draining all the water and the clothes were dripping. That might be the cause of your problem.
At first all it wouldn't do was fast spin, but it did everything else. Now it has stopped rotating altogether; what could the problem be?
By Sam
You did not provide the washer brand, year model, etc., so difficult to help you. However, you can check the product booklet for possibilities, ask the store where purchased, and also check the manufacturer's website for help-customer service.
It spins with nothing in it, but with clothes it barely spins. I changed the belt and the motor sounds like it's rattling.
By Elmer T.
I have a Frigidaire front load washer and the drum and pulley won't spin. It feels like it's locked but when I apply a little pressure to spin the pulley it becomes unlocked and spins. When I start the washer it locks up again after a few minutes.
By Reggie M
My bosch was doing this. I called out a repair person, and it turns out the washer was no longer level. We leveled it and all was fine again. Make sure its level.
My GE front loader won't spin/drain at the end of the cycle. The washer goes through the whole cycle fine, but won't spin to drain out the water at the end. I changed the catch basin and it is still not working.
By B. J. from MO
Looking for an answer to this question, been on here for two days and the only thing I get is to clean the drain pump. Is there someone out there who really knows the answer to this question?
My front loading Kenmore washer model #417 sounds like it is spinning, but does not even though the belt is fine.
By John F
The drive shaft may be worn. Call the repair man. I have had that happen.
I have a Frigidaire Affinity washer, model number ATF6500FG0. It will not go into the spin cycle. The washer does everything else, but won't go into the spin cycle.
By Cliff Law from Cochrane AB Canada
Not sure about yours, but my front loader had a built in filter and it got clogged and wouldn't spin, opened the a little door on the front cleaned it out and works like new. I hope this helps, try calling the company and asking them what the problem could be. It could be minor and they might tell you over the phone.
My Hotpoint front-loader spins only when empty or with the motor removed from the machine. All else appears fine.
By Alex
You may need a new belt. That's been my problem. Good luck! carmen1951
We have Frigidaire Gallery series stacked washer and dryer. The washer make a loud bang and is making a noise when spinning. Also the clothes are not spinning dry as they normally do. I think this could be a popped spring - however is this all it could be? Any help is appreciated as I usually repair our appliances.
Thank you.
You could have a faulty lid switch, a broken belt or a problem with the motor.
I have a Frigidaire front loader and it will run water for a time and not long and won't spin. Then sometime after that it will shut off. What could it be?
By Crystal
This could be a problem with your control panel and a belt in the washer. If the tub is filling with water and it reached the water level the indicator should trigger the circuit board to start the wash cycle.
There could be a problem with the inlet valve or the sensor letting the machine know its full and to start washing.