social

Repairing a Gas Powered Trimmer

July 15, 2012

After a couple years of reliable use, my Homelite Mighty Lite gas powered trimmer began to have trouble running when I turned the choke off after starting it. If you own one of these, or other similar two-stroke engines, you are familiar with the process of starting one up - have the choke on full to begin with, then after it stops, switch it to half-choke and let it run until the engine is warm up. Then you can switch it to "Run" mode and that turns the choke all the way off.

Advertisement

Mine would only work if I had it on half choke and I could tell I wasn't getting full power. After a while I couldn't get it to run at all, unless the choke was all the way open. Obviously that doesn't do much good as the trimmer won't engage and the engine doesn't run for more than a few seconds at a time.

Since the engine turned over fine, I figured the problem was a lack of fuel getting to the spark plug. It turns out that is exactly the case. Over time, these engines often develop a diminished fuel flow that will cause the engine to stall. Fortunately, this problem is relatively easy to fix.

There are 2 screws that control the fuel flow. Unfortunately, these screws don't have heads and are slightly recessed. The trick is to cut into the top of them, so you can use a flathead screwdriver to adjust their height.

Advertisement

To start with, remove the circular plastic air filter that is also the choke adjustment knob. This held on by a nut with a washer so it is easy to remove.

Homelite "Mighty Lite" Gas Powered Trimmer
 

Next, you will need to locate the screws you need to adjust. When you remove the air filter, it looks like this underneath. The screw in the very center of the photo is the idle adjustment screw. This screw is always accessible through the hole in the plastic cover that serves as the choke adjustment guide. This is not the screw we are looking for but it is a good reference point.

Air Filter Removed on Homelite "Mighty Lite" Gas Powered Trimmer
 

Look just below the idle adjustment screw and you will see this. That small aluminum housing with the two flat machine screws is what we are looking for.

Mighty Lite Screws Before Being Cut
 

A Dremel tool works best for this step but I am sure a narrow hacksaw could do the trick. Using the Dremel, cut straight across the top of the screws and the housing until it looks like this (well yours might be prettier but you get the idea).

Cutting Mighty Lite Screws With Dremel
 
Mighty Lite With Screws Cut for Flathead
 

Then, using a narrow flathead screwdriver, tighten the screws all the way down by turning the clockwise. That should about 1 1/2 turns, as that is the factory setting for the screws. Once they are tightened down, unscrew them (counter clockwise) 2 full turns. That will open up the fuel flow to the engine.

Adjusting Fuel Flow on Mighty Lite
 

Put the air filter back on and start it up. It should run just fine now. Mine was still sputtering just a bit so I went back and unscrewed them another quarter turn and now my trimmer runs great. With the additional fuel flow you may want to adjust the idle down a bit now, but only if necessary.

Advertisement

By Jess from Hillsboro, OR

Read More Comments

Videos

October 2, 2014

If your gas powered trimmer is having trouble running when you turn the choke off after starting it, this tip may help you. Check out how we fixed this problem.

<< First< Previous
Categories
Home and Garden Repair ToolsJuly 14, 2012
Pages
More
👒
Mother's Day Ideas!
🐰
Easter Ideas!
🌻
Gardening
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-03-28 08:05:01 in 4 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/Repairing-a-Gas-Powered-Trimmer.html